Custom Gear Manufacturing: Spur, Helical and Worm Gears, and How to Specify Them

Published November 2026  ·  10 min read  ·  Buyer's Guide  ·  Machining

A gear quote is only as good as the gear data behind it. Module, number of teeth, pressure angle, helix angle, profile shift, accuracy grade, material and heat treatment all change the price and the result, and missing one of them is the most common reason a replacement gear does not mesh. This guide explains the main gear types, the data a gear drawing must carry, typical materials and accuracy grades, and includes a calculator for pitch, tip and root diameters and centre distance.

Quick answers
• Spur gears: straight teeth, simple and efficient, but noisier at speed. Helical gears: angled teeth, quieter and stronger, but create axial thrust. Worm gears: high ratios in one stage and possible self-locking, with lower efficiency.
• The basic size parameter in Europe is the module (m, in mm): pitch diameter d = m × z. In the US it is diametral pitch (DP): m = 25.4 / DP.
• The standard pressure angle is 20° (ISO 53 basic rack). 14.5° and 25° exist; gears with different pressure angles do not mesh correctly.
• Specify accuracy to ISO 1328-1, DIN 3961/3962 or AGMA 2015. Hobbed gears are typically around grade 8–10; ground gears reach about 4–6.
• Common steels: 16MnCr5 / 20MnCr5 (case-carburised), 18CrNiMo7-6 (heavy duty), 42CrMo4 (through-hardened or induction-hardened), C45 (general purpose). Worm wheels are usually bronze (e.g. CuSn12).

Main Gear Types and Where They Are Used

TypeShaftsStrengthsLimitationsTypical use
SpurParallelSimple, cheap to make, high efficiency (about 98–99% per stage), no axial loadNoisier at high speed, lower load capacity than helical of the same sizeGearboxes, pumps, machine tools, conveyors, agricultural machinery
HelicalParallel (or crossed)Quieter and smoother, more teeth in contact, higher load capacityAxial thrust needs suitable bearings; slightly more complex to makeIndustrial gearboxes, automotive transmissions, compressors
Double helical / herringboneParallelHelical smoothness without net axial thrustMore expensive, needs exact alignmentHeavy industrial drives, mills, turbines
Worm and wheelCrossed at 90°, non-intersectingHigh ratio in one stage (typically 5:1 to 100:1), compact, quiet, can be self-lockingLower efficiency (roughly 50–90% depending on lead angle), heat generation, bronze wheel wearsHoists, gates, lifting tables, conveyors, valve actuators
Bevel (straight / spiral)Intersecting, usually 90°Changes direction of driveNeeds precise mounting distance; spiral bevels need special machinesRight-angle gearboxes, differentials, power tools
Rack and pinionRotary to linearSimple linear motion over long travelBacklash at reversal unless preloadedGantries, sliding gates, CNC machines, lifts
Internal (ring) gearParallelCompact, used in planetary setsMade by shaping, broaching or skiving, not hobbingPlanetary gearboxes, winches, slewing drives

Gear Geometry Basics: Module, Pitch and Pressure Angle

For a standard involute spur gear without profile shift, the main diameters follow directly from the module and the number of teeth. Two gears mesh correctly only if they have the same module (or DP) and the same pressure angle; helical gears must also have the same helix angle with opposite hands (for parallel shafts).

QuantitySpur gear formulaExample: m = 3, z = 40
Pitch (reference) diameter dd = m × z120 mm
Tip (outside) diameter dada = m × (z + 2)126 mm
Root diameter dfdf = m × (z − 2.5)112.5 mm
Whole depth hh = 2.25 × m6.75 mm
Circular pitch pp = π × m9.42 mm
Centre distance a (pair)a = m × (z1 + z2) / 2with z2 = 20: 90 mm
Helical: pitch diameterd = mn × z / cos βmn = 3, z = 40, β = 15°: 124.23 mm
Module ↔ diametral pitchm = 25.4 / DPDP 8 ≈ m 3.175
Profile shift changes the diameters. Many industrial gears use a profile shift coefficient (x) to avoid undercut on small pinions, balance strength or hit a fixed centre distance. With profile shift, tip and root diameters and the centre distance differ from the table above. If you are replacing a worn gear, measure the tip diameter and the span over k teeth (Wk) and send them with the tooth count, so the manufacturer can calculate the shift.

Gear Calculator: Diameters, Centre Distance and Ratio

Enter the module (or diametral pitch), tooth counts, pressure angle and helix angle. The calculator gives standard values for gears without profile shift.

Standard full-depth teeth (addendum 1.0 m, dedendum 1.25 m), normal-module basis for helical gears, no profile shift. Use for checking and quoting, not for final design.

What a Gear Drawing or RFQ Must Include

Gear drawings carry a data table next to the drawing. If you send only a 3D model or a photo, the manufacturer has to guess. The table below is the minimum for a quotable cylindrical gear.

  • Number of teeth (z) and module (m or mn) or diametral pitch
  • Pressure angle (normally 20°) and basic rack profile (e.g. ISO 53 profile A)
  • Helix angle and hand (left / right) for helical gears; lead angle and number of starts for worms
  • Profile shift coefficient (x) or the tooth thickness / span measurement Wk over k teeth, or dimension over pins/balls
  • Face width, bore, keyway or spline, hub and chamfers
  • Accuracy grade (e.g. ISO 1328-1 grade 7, DIN 3962 quality 8) and backlash or tooth thickness tolerance
  • Material and heat treatment: grade, hardness (surface and core), case depth for carburised or induction-hardened gears
  • Mating gear data and centre distance, so the pair can be checked together
  • Quantity, certificates (EN 10204 3.1 for material, hardness and inspection reports) and delivery terms

Our RFQ guide for custom metal parts covers the general items (files, tolerances, finishes, Incoterms) that apply to gears as well.

Gear Materials and Heat Treatment

MaterialTypical treatmentTypical surface hardnessUse
16MnCr5 / 20MnCr5 (EN 10084)Case carburising + hardening, then grinding58–62 HRC, tough coreMost industrial and automotive gearbox gears
18CrNiMo7-6Case carburising58–62 HRC, higher core strengthHeavily loaded, large gears (wind, mining, marine)
42CrMo4 (EN 10083-3)Quenched and tempered; optionally induction or nitridedQT about 28–34 HRC; induction about 50–55 HRCMedium-load gears, large gears, shafts with integral gears
C45 (EN 10083-2)Normalised or induction hardenedNormalised about 170–210 HB; induction about 50–55 HRCGeneral-purpose, lower-load gears, racks
Grey / ductile cast iron (EN-GJL-250, EN-GJS-600)As cast or heat treatedAbout 180–270 HBLarge, low-speed gears, damping noise
Bronze (CuSn12, CuSn12Ni2)Cast (often centrifugally)About 80–110 HBWorm wheels running against hardened steel worms
Stainless steel (1.4057, 1.4542)Hardened and tempered / precipitation hardenedDepends on gradeFood, chemical and marine equipment
Engineering plastics (POM, PA)Machined or moulded–Light loads, quiet running, no lubrication

Hardness values are typical ranges; the drawing must state the required values and case depth.

Manufacturing Processes and Accuracy Grades

The process determines the achievable accuracy and the price. For most industrial gears, teeth are hobbed (external spur and helical) or shaped (internal gears and gears close to a shoulder), then heat treated, and finally ground if high accuracy or low noise is required. Internal splines are often broached. Worms are milled or ground; worm wheels are hobbed with a tool matched to the worm.

ProcessTypical accuracy (ISO 1328-1 / DIN 3962)Notes
Hobbing (soft)about 8–10Most economical for external spur and helical gears
Hobbing + heat treatment (no finishing)about 9–10Distortion from hardening lowers accuracy
Shapingabout 8–9Internal gears, cluster gears, gears next to shoulders
Shaving (before hardening)about 7–8Common in medium-volume automotive production
Grinding (after hardening)about 4–6Highest accuracy, low noise; higher cost
Choose the grade the application needs. Each step to a finer accuracy grade increases cost. Slow, open drives may work well at grade 9–10, while high-speed gearboxes often need grade 6 or better. Note that grade numbers run in opposite directions in some systems: in ISO and DIN a lower number is more accurate, while in the older AGMA 2000 "Q" system a higher number is more accurate.

Replacing a Worn or Obsolete Gear

Many buyers need a replacement for a gear with no drawing. A manufacturer can reverse-engineer it from a sample or a measured sketch if you provide: tooth count, tip diameter, span over k teeth (Wk) or over-pin dimension, face width, bore and keyway, helix angle and hand (measured with a roll print or estimated from the lead), and the mating gear's tooth count and centre distance. A hardness reading on an unworn area helps choose the material. Sending both gears of the pair gives the most reliable result.

Custom Gears from Türkiye

Turkish gear manufacturers supply spur, helical, worm, bevel and rack gears, gear shafts and complete gearbox parts to machinery builders and maintenance buyers in Europe, the Middle East and beyond, from single replacement gears to series production. Steeling.net matches your gear drawing or sample data with suitable partner manufacturers for gear manufacturing and CNC machining, and coordinates heat treatment, inspection reports and delivery. There are no fees for buyers.

Frequently Asked Questions

What is the difference between spur and helical gears?

Spur gears have straight teeth parallel to the axis; they are simple, efficient and create no axial thrust, but are noisier at high speeds. Helical gears have teeth cut at an angle, so several teeth are in contact at once; they run more quietly and carry more load, but generate axial thrust that the bearings must handle.

How do I calculate the pitch diameter of a gear?

For a spur gear, multiply the module by the number of teeth: d = m × z. A gear with module 3 and 40 teeth has a pitch diameter of 120 mm. For a helical gear, divide by the cosine of the helix angle: d = mn × z / cos β. For gears specified in diametral pitch, d (inches) = z / DP.

How do I convert diametral pitch to module?

Module (mm) = 25.4 / diametral pitch. For example, DP 8 corresponds to a module of about 3.175 mm, which is not a standard metric module, so metric and inch gears are generally not interchangeable.

Are worm gears self-locking?

Worm gears with a small lead angle (typically single-start worms with a lead angle below about 5°) tend to be self-locking, meaning the wheel cannot drive the worm. However, vibration and lubrication can overcome this, so self-locking should not replace a brake in lifting or safety-critical applications.

What accuracy grade should I specify for a gear?

It depends on speed, load and noise requirements. Slow, open drives often work at ISO 1328-1 or DIN grade 9–10, general industrial gearboxes at grade 7–8, and high-speed or low-noise gearboxes at grade 6 or better, which usually requires grinding after hardening.

What information is needed to make a replacement gear without a drawing?

Provide the tooth count, tip diameter, span measurement over k teeth or over-pin dimension, face width, bore and keyway, helix angle and hand if helical, the mating gear's tooth count and the centre distance. Sending the worn gear and its mating gear as samples gives the most reliable result.

Need custom or replacement gears?

Send your gear drawing or sample data, quantity and destination. Steeling.net returns offers from qualified Turkish gear manufacturers, including heat treatment and inspection reports. There are no fees for buyers.

Request a Quote →