SHS, RHS and CHS Hollow Section Sizes and Weights: EN 10219 vs EN 10210
Published November 2026 · 9 min read · Technical Reference · Structural Steel
Square, rectangular and circular hollow sections are used for columns, trusses, frames, handrails, machine bases and trailers. They are efficient in compression and torsion and look clean in exposed structures. This guide gives weight tables for the common SHS, RHS and CHS sizes, explains the difference between cold-formed EN 10219 and hot-finished EN 10210 sections, and lists the grades, equivalents and order details you need.
• SHS = square hollow section, RHS = rectangular hollow section, CHS = circular hollow section.
• EN 10219: cold-formed welded sections. They are the most common and most economical.
• EN 10210: hot-finished sections, with tighter corners, lower residual stresses and better buckling resistance.
• Typical grades: S235JRH, S275J0H, S355J2H. The "H" stands for hollow section.
• Example: SHS 100 × 100 × 4 weighs about 11.7 kg/m.
EN 10219 vs EN 10210: What Is the Difference?
| EN 10219 (cold-formed) | EN 10210 (hot-finished) | |
|---|---|---|
| Process | Strip is formed into a tube and welded at room temperature, then shaped to square or rectangular | Formed hot, or formed cold and then heat-treated (normalised) to remove forming stresses |
| Corner radius (outside) | About 2–3 × t | About 1.5 × t (sharper corners) |
| Residual stress | Higher, especially at the corners | Low |
| Buckling curve (EN 1993-1-1) | Curve c | Curve a (a0 for S460) |
| Section properties | Slightly lower for the same nominal size | Slightly higher |
| Price and availability | Lower price, widely stocked | Higher price, fewer producers |
| Typical use | Most buildings, frames, fences, trailers, furniture, machine frames | Heavily loaded columns, bridges, offshore, fatigue-loaded structures |
The two standards use the same nominal size designations, but the sections are not interchangeable in a design. A column designed with EN 10210 buckling resistance may fail the check if it is replaced with an EN 10219 section of the same size. Always confirm which standard the engineer used.
Weight Calculator
Weights for EN 10219 cold-formed sections, calculated with the standard corner radii and a density of 7,850 kg/m³. Other sizes: use our steel weight calculator.
SHS Weight Table: Square Hollow Sections (kg/m)
| SHS B × B (mm) | t = 1.5 | t = 2 | t = 2.5 | t = 3 | t = 4 | t = 5 | t = 6 | t = 8 | t = 10 | t = 12.5 |
|---|---|---|---|---|---|---|---|---|---|---|
| 20 × 20 | 0.83 | 1.05 | 1.25 | – | – | – | – | – | – | – |
| 25 × 25 | 1.06 | 1.36 | 1.64 | 1.89 | – | – | – | – | – | – |
| 30 × 30 | 1.30 | 1.68 | 2.03 | 2.36 | – | – | – | – | – | – |
| 40 × 40 | 1.77 | 2.31 | 2.82 | 3.30 | 4.20 | 4.99 | – | – | – | – |
| 50 × 50 | 2.24 | 2.93 | 3.60 | 4.25 | 5.45 | 6.56 | 7.56 | – | – | – |
| 60 × 60 | 2.71 | 3.56 | 4.39 | 5.19 | 6.71 | 8.13 | 9.45 | – | – | – |
| 70 × 70 | 3.18 | 4.19 | 5.17 | 6.13 | 7.97 | 9.70 | 11.33 | 13.85 | – | – |
| 80 × 80 | – | 4.82 | 5.96 | 7.07 | 9.22 | 11.27 | 13.21 | 16.36 | 19.28 | – |
| 90 × 90 | – | 5.45 | 6.74 | 8.01 | 10.48 | 12.84 | 15.10 | 18.87 | 22.42 | – |
| 100 × 100 | – | 6.07 | 7.53 | 8.96 | 11.73 | 14.41 | 16.98 | 21.39 | 25.56 | 29.08 |
| 120 × 120 | – | – | 9.10 | 10.84 | 14.25 | 17.55 | 20.75 | 26.41 | 31.84 | 36.93 |
| 140 × 140 | – | – | – | 12.72 | 16.76 | 20.69 | 24.52 | 31.43 | 38.12 | 44.78 |
| 150 × 150 | – | – | – | – | 18.01 | 22.26 | 26.40 | 33.95 | 41.26 | 48.70 |
| 160 × 160 | – | – | – | – | 19.27 | 23.83 | 28.29 | 36.46 | 44.40 | 52.63 |
| 180 × 180 | – | – | – | – | 21.78 | 26.97 | 32.05 | 41.48 | 50.68 | 60.48 |
| 200 × 200 | – | – | – | – | 24.29 | 30.11 | 35.82 | 46.51 | 56.96 | 68.33 |
| 250 × 250 | – | – | – | – | – | 37.96 | 45.24 | 59.07 | 72.66 | 87.95 |
| 300 × 300 | – | – | – | – | – | – | 54.66 | 71.63 | 88.36 | 107.58 |
RHS Weight Table: Rectangular Hollow Sections (kg/m)
| RHS H × B (mm) | t = 1.5 | t = 2 | t = 2.5 | t = 3 | t = 4 | t = 5 | t = 6 | t = 8 | t = 10 | t = 12.5 |
|---|---|---|---|---|---|---|---|---|---|---|
| 40 × 20 | 1.30 | 1.68 | 2.03 | 2.36 | 2.94 | – | – | – | – | – |
| 50 × 25 | 1.65 | 2.15 | 2.62 | 3.07 | 3.88 | 4.60 | – | – | – | – |
| 50 × 30 | 1.77 | 2.31 | 2.82 | 3.30 | 4.20 | 4.99 | 5.68 | – | – | – |
| 60 × 40 | 2.24 | 2.93 | 3.60 | 4.25 | 5.45 | 6.56 | 7.56 | – | – | – |
| 80 × 40 | – | 3.56 | 4.39 | 5.19 | 6.71 | 8.13 | 9.45 | 11.34 | – | – |
| 100 × 50 | – | 4.50 | 5.56 | 6.60 | 8.59 | 10.48 | 12.27 | 15.11 | 17.71 | – |
| 100 × 60 | – | 4.82 | 5.96 | 7.07 | 9.22 | 11.27 | 13.21 | 16.36 | 19.28 | – |
| 120 × 60 | – | – | 6.74 | 8.01 | 10.48 | 12.84 | 15.10 | 18.87 | 22.42 | – |
| 120 × 80 | – | – | 7.53 | 8.96 | 11.73 | 14.41 | 16.98 | 21.39 | 25.56 | 29.08 |
| 150 × 100 | – | – | – | – | 14.87 | 18.33 | 21.69 | 27.67 | 33.41 | 38.89 |
| 160 × 80 | – | – | – | – | 14.25 | 17.55 | 20.75 | 26.41 | 31.84 | 36.93 |
| 200 × 100 | – | – | – | – | 18.01 | 22.26 | 26.40 | 33.95 | 41.26 | 48.70 |
| 250 × 150 | – | – | – | – | – | 30.11 | 35.82 | 46.51 | 56.96 | 68.33 |
| 300 × 200 | – | – | – | – | – | – | 45.24 | 59.07 | 72.66 | 87.95 |
CHS Weight Table: Circular Hollow Sections (kg/m)
| CHS outside Ø (mm) | t = 2 | t = 2.6 | t = 3 | t = 3.2 | t = 4 | t = 5 | t = 6.3 | t = 8 | t = 10 |
|---|---|---|---|---|---|---|---|---|---|
| 21.3 | 0.95 | – | – | – | – | – | – | – | – |
| 26.9 | 1.23 | 1.56 | – | – | – | – | – | – | – |
| 33.7 | 1.56 | 1.99 | 2.27 | 2.41 | – | – | – | – | – |
| 42.4 | 1.99 | 2.55 | 2.91 | 3.09 | 3.79 | – | – | – | – |
| 48.3 | 2.28 | 2.93 | 3.35 | 3.56 | 4.37 | 5.34 | – | – | – |
| 60.3 | 2.88 | 3.70 | 4.24 | 4.51 | 5.55 | 6.82 | 8.39 | – | – |
| 76.1 | 3.65 | 4.71 | 5.41 | 5.75 | 7.11 | 8.77 | 10.84 | 13.44 | – |
| 88.9 | 4.29 | 5.53 | 6.36 | 6.76 | 8.38 | 10.35 | 12.83 | 15.96 | – |
| 114.3 | 5.54 | 7.16 | 8.23 | 8.77 | 10.88 | 13.48 | 16.78 | 20.97 | 25.72 |
| 139.7 | 6.79 | 8.79 | 10.11 | 10.77 | 13.39 | 16.61 | 20.73 | 25.98 | 31.99 |
| 168.3 | – | 10.62 | 12.23 | 13.03 | 16.21 | 20.14 | 25.17 | 31.63 | 39.04 |
| 219.1 | – | – | – | – | 21.22 | 26.40 | 33.06 | 41.65 | 51.57 |
| 273 | – | – | – | – | 26.54 | 33.05 | 41.44 | 52.28 | 64.86 |
| 323.9 | – | – | – | – | – | 39.32 | 49.34 | 62.32 | 77.41 |
Calculated from nominal dimensions for EN 10219 cold-formed sections: outside corner radius 2t (t ≤ 6 mm), 2.5t (6 < t ≤ 10 mm) and 3t (t > 10 mm). Hot-finished EN 10210 sections of the same size are slightly heavier because of their smaller corner radii. Not every size and thickness is stocked by every mill. "–" means the combination is uncommon.
Steel Grades for Hollow Sections
| Grade | Min. yield strength (t ≤ 16 mm) | Impact test | Typical use | Nearest US grade |
|---|---|---|---|---|
| S235JRH | 235 MPa | 27 J at +20 °C | Fences, gates, light frames, furniture | ASTM A500 Gr. A (approx.) |
| S275J0H | 275 MPa | 27 J at 0 °C | General structures | ASTM A500 Gr. B (approx.) |
| S355J2H | 355 MPa | 27 J at −20 °C | Building columns and trusses, trailers, machine frames | ASTM A500 Gr. C / A1085 (approx.) |
| S420MH / S460MH | 420 / 460 MPa | 40 J at −20 °C | Lightweight high-strength structures, cranes | – |
For CE-marked structural work under EN 1090, ask for an EN 10204 3.1 certificate. Hollow sections that will be hot-dip galvanized need suitable silicon and phosphorus content and vent holes in the fabricated part, so tell the supplier in advance.
Where Hollow Sections Outperform Open Sections
Columns and struts
The same stiffness in both directions gives high buckling resistance. An SHS column is often lighter than an HEA column for the same axial load.
Trusses and space frames
Members can be welded directly to each other without gusset plates, which gives clean joints.
Torsion
Closed sections are many times stiffer in torsion than I-sections. They are ideal for trailer chassis, machine bases and cantilever arms.
Exposed and architectural steel
Smooth surfaces are easier to paint and clean, and offer a smaller surface area to protect against corrosion and fire.
For beams that carry bending loads in one direction, IPE and HEA/HEB sections are usually more economical.
How to Order Hollow Sections
- Type and size: for example SHS 100 × 100 × 5, RHS 120 × 80 × 4 or CHS 114.3 × 4.
- Standard: EN 10219 (cold-formed) or EN 10210 (hot-finished). Do not leave this open.
- Grade: for example S355J2H.
- Length: 6 m and 12 m are standard. Other lengths and exact cut lengths are possible on order.
- Surface: black, primed, pre-galvanized (for thin sections) or hot-dip galvanized.
- Ends: square cut, mitred or with drilled holes, if fabricated.
- Certificate: EN 10204 3.1 as standard, 3.2 if your project requires third-party inspection.
- Packing: hexagonal or square bundles, strapped, with bundle weight limits for your crane.
Sourcing Hollow Sections from Türkiye
Türkiye is one of Europe's largest producers of welded tubes and hollow sections. Turkish mills produce EN 10219 SHS, RHS and CHS in a wide range of sizes and grades up to S355J2H and above, with CE marking and 3.1 certificates. Many also cut, drill, bend and galvanize them. Truck deliveries to the Balkans and Central Europe and short sea transit to Mediterranean ports keep lead times short.
See our hollow sections from Türkiye range, or send us your size list for a quotation.
Frequently Asked Questions
What is the difference between SHS and RHS?
SHS (square hollow section) has equal width and height, for example 100 × 100 mm. RHS (rectangular hollow section) has different width and height, for example 120 × 80 mm, which gives more bending stiffness about one axis.
What is the difference between EN 10219 and EN 10210?
EN 10219 covers cold-formed welded hollow sections, which are more economical and widely stocked. EN 10210 covers hot-finished hollow sections, which have smaller corner radii, lower residual stresses and a better buckling curve. They are not interchangeable in a structural design without a new check.
How much does a 100 × 100 × 4 SHS weigh?
A cold-formed SHS 100 × 100 × 4 to EN 10219 weighs about 11.7 kg per metre, so a 6 m length weighs about 70 kg.
What does the "H" in S355J2H mean?
The "H" indicates that the grade is for hollow sections. S355J2H has a minimum yield strength of 355 MPa and guaranteed impact energy of 27 J at −20 °C.
What is the US equivalent of EN 10219 hollow sections?
The nearest US standard is ASTM A500 for cold-formed welded structural tubing, with grades B and C. ASTM A1085 has tighter tolerances and is closer in performance to European structural hollow sections. The equivalence is approximate.
What is the HS code for square steel tubes?
Welded square and rectangular tubes and hollow sections of iron or non-alloy steel are usually classified under HS 7306.61. Circular welded tubes of non-alloy steel are usually under 7306.30, and seamless tubes under 7304.
Send your size list, grade and quantities. Steeling.net returns offers from selected Turkish tube mills with 3.1 certificates, cut-to-length and galvanizing options. There are no fees for buyers.
Get a Free Quote →